Zancot Electronics

motion servo drive LXM05A - 1.4 kW - 380..480 V - 3-phase - with EMC filter LXM05AD14N4 Motion servo drive LXM05A - 1.4 kW - 380..480 V - 3-phase - with EMC filter. Nominal power: 14 kW. Power supply voltage: 380…480 V

Part number MR-J4-350A is a Melservo J4 series servo amplifier with one (1) axis. This device was designed and produced by the manufacturer Mitsubishi Electric. The MR-J4-350A is compatible with only one (1) servo motor at a time due to it having a single axis. It comes with a general-purpose interface, which is suitable for standard operations. The HG-SR352 and HG-SR301 servo motors are compatible with the MR-J4-350A servo amplifier. The rated output power of this unit is 3.5 watts. It has a 170-Volt AC output voltage rating, in addition to a 17-ampere output current rating. The three-phase power supply of this amplifier ranges from 200 VAC and 240 VAC at a frequency of 50 to 60 hertz. This unit''s three-phase rated current rating is 16.0 amperes at the provided voltage. The permissible voltage fluctuation for three-phase operations is between 170 VAC and 264 VAC, and the permissible frequency fluctuation is +/- 5%. For single-phase operations, the control circuit power supply runs between 200 Volts AC and 240 Volts AC at 50 to 60 hertz and a current of 0.2 amperes. The MR-J4-350A is a PWM-compatible module. The PWM (Pulse Width Modulation) control system can turn on and off the transistors in the inverter section to adjust the voltage going to the motor. Furthermore, this module has built-in dynamic brakes for intelligently controlling servo motors. This unit weighs approximately 2.3 kilograms or 5.07 pounds. In addition, this servo amplifier has dimensions that measure 168 mm (height) x 90 mm (width) x 195 mm (depth).

The MR-J2S-100A is a servo amplifier from Mitsubishi Electric. It is a 3-phase servo amplifier with a 200 to 230-volt AC voltage supply and a 50 to 60 Hz frequency range. This servo device includes various features that are beneficial for motors used in industrial settings. Its power supply range for the permissible voltage fluctuation is 170 to 253 volts AC, and the frequency fluctuation is ±5%. It supports sinusoidal pulse width modulation (PWM) control and the current control system. It comes with built-in dynamic braking functionality, unlike many modules in the same series. Additionally, the MR-J2S-100A's

speed frequency response range can go up to 550 Hz or more. Excess error protection, over-speed protection, and under-voltage/ sudden power outage protection features are supported by this servo amplifier. Aside from these features, it can work with the over-current shutdown, regeneration overvoltage shutdown, and overload shutdown protective features. In addition, the max input pulse frequency is 500 kbps when used in position control mode. However, it is 200 kbps when using a differential receiver mode. Its max speed fluctuation rate is 0.01%. Additionally, its load fluctuation ranges from 0% to 100%. Likewise, its power fluctuation ranges from 0% to 10%. When using the external analog speed command, the outside temperature should be between 10 °C and 25 °C. In addition, its maximum torque can be controlled by various parameters or external analog input. This device also comes in a self-cooling (IP00) structure to dissipate heat and offers an overall durable build quality.

VW3M8102R50 - SinCos Hiperface encoder cable, Lexium, 3 x (2 x 0.14mm) + (2 x 0.34mm), 5m - Schneider Electric

The Mitsubishi Electric MR-J2S-10A is a servo amplifier. It belongs to the Melservo J2 Super series of products. This device offers control functions to mechanical servo motors. This module works as a drive for a wide range of servo motors used in the power automation, manufacturing, and other processing industries. It operates with a 200-volt AC power supply. Additionally, the operating frequency range of this module is 50 to 60 Hz. In addition to that, this device has a power supply rating of 230 volts AC at 50/60 Hz for its single-phase operation mode. The MR-J2S-10A servo amplifier can load 10 amperes of current. This device consumes less current compared to some of the other servo amplifiers in the same series. This product from Mitsubishi Electric has dimensions that measure 168 millimeters (height) x 50 millimeters (width) x 205 millimeters (depth). The ambient operating temperature of this servo amplifier device ranges from 0 degrees Celsius to 55 degrees Celsius. Failure to observe this range for the MR-J2S-10A's operation can result in an unnecessary unit malfunction. Therefore, it is highly recommended that the users should always maintain the standard operating temperature. This module also supports a wide variety of protective functions which keep the hardware unit of the motors safe from sudden changes in the power. For example, it provides excellent precision overcurrent and voltage and ensures the stability of the performance of its compatible motors and machines. The Mitsubishi Electric MR-J2S-10A has a shipping weight of approximately three (3) kilograms.

he MR-J2S-100A is a servo amplifier from Mitsubishi Electric. It is a 3-phase servo amplifier with a 200 to 230-volt AC voltage supply and a 50 to 60 Hz frequency range. This servo device includes various features that are beneficial for motors used in industrial settings. Its power supply range for the permissible voltage fluctuation is 170 to 253 volts AC, and the frequency fluctuation is ±5%. It supports sinusoidal pulse width modulation (PWM) control and the current control system. It comes with built-in dynamic braking functionality, unlike many modules in the same series. Additionally, the MR-J2S-100A's

speed frequency response range can go up to 550 Hz or more. Excess error protection, over-speed protection, and under-voltage/ sudden power outage protection features are supported by this servo amplifier. Aside from these features, it can work with the over-current shutdown, regeneration overvoltage shutdown, and overload shutdown protective features. In addition, the max input pulse frequency is 500 kbps when used in position control mode. However, it is 200 kbps when using a differential receiver mode. Its max speed fluctuation rate is 0.01%. Additionally, its load fluctuation ranges from 0% to 100%. Likewise, its power fluctuation ranges from 0% to 10%. When using the external analog speed command, the outside temperature should be between 10 °C and 25 °C. In addition, its maximum torque can be controlled by various parameters or external analog input. This device also comes in a self-cooling (IP00) structure to dissipate heat and offers an overall durable build quality.

The MR-J3-10B is an AC servo amplifier from Mitsubishi Electric that is compatible with numerous servo motors. This servo amplifier is part of the Melservo J3 product family. Catalog number MR-J3-10B provides control command features to the connected servo motors. This product also generates torque and velocity depending on the current and voltage inputs. The MR-J3-10B can convert a motion controller''''s low power command signal into a high power current or voltage. This product''''s voltage rating is 200 to 230 VAC at a 50/60-hertz frequency. Additionally, the MR-J3-10B has a 0.9-ampere current rating. The output voltage rating of this module is 170 VAC with an output current rating of 1.1 amperes. The inverse efficiency rating of this product is 55 percent. The interface power supply of the MR-J3-10B is 24 VDC +/- 10% with a required current capacity of 0.15 amperes. This servo amplifier features two (2) control systems. These systems include the Current Control system, as well as the Sine-wave Pulse Width Modulation (PWM) Control system. Additionally, this unit features a built-in dynamic brake. The enclosure of this device is classified as a natural-cooling, open-type enclosure with an Ingress Protection rating of IP00. The weight of the MR-J3-10B is approximately 0.8 kilograms or the equivalent of 1.8 pounds. This servo amplifier may be connected to power supplies via the use of cables/wires with a size of 14 AWG. The ambient temperature recommended for this unit''''s operation ranges from 0 to 55 degrees Celsius. Additionally, the ambient temperature recommended for this unit''''s storage ranges from -20 to 65 degrees Celsius.

GuardLogix Integrated Safety PAC with 4M standard memory & 2M safety memory - Conformally Coated. A safety partner is required for each 1756 GuardLogix controller.

ControlLogix Logix5572 Processor with 4MB User Memory, 0.98MB I/O memory; 128,000 Digital I/O, 4,000 Analog I/O; 1-USB Port USB 2.0, full speed, 12 Mbps (EtherNet/IP, ControlNet, DeviceNet, Data Highway Plus, Remote I/O, SynchLink, Third-party process and device networks)

PLC-5 Digital DC Output Module, 16 Outputs, 10-32V DC, Isolated, Conformally Coated

1756-L71 ControlLogix Logix5571 Processor with 2 Mbytes Memory

10-30 VDC Sourcing Input 16 Pts (20 Pin) - Conformally Coated

Servo amplifier applicable with general-purpose interface.Position control by pulse train command and speed/torque control by analog voltage command are possible.It supports maximum command pulse frequency of 4 M pulses/s.

The Mitsubishi Electric MR-J4-60A Melservo J4 servo amplifier belongs to the 200-Volt AC class of amplifiers. This device is equipped with a general-purpose command interface. The output power rating of this unit is 600 watts. Additionally, the power supply voltage of this unit ranges from 200 Volts AC to 240 Volts AC. It has a 50to 60-hertz frequency rating and is compatible with one and three-phase power supply connections. This servo amplifier is compatible with various servo motors, such as catalog numbers HG-SR51, HG-SR52, and HG-JR53. This device can be used for a variety of servo applications. For instance, it is feasible to control position using a pulse train command and speed/torque using an analog voltage command. The greatest command pulse frequency it supports is 4 M pulses/second. Mitsubishi's high-speed serial optical communication allows users to create the most accurate synchronization systems. Similarly, users can connect this servo amplifier to a servo system controller to maximize the features and performance of the servo system. Its safety function type is STO (IEC/EN 61800-5-2). The MR-J4-60A complies with UKCA, CE, UL, and cUL standards. The design of this amplifier is compact. It weighs about 1.0 kilogram and has dimensions consisting of a 40-millimeter width, a 168-millimeter height, and a 170-millimeter depth. The MR-J4-60A is equipped with dynamic brakes. It also provides two (2) control methods to its users. These control methods are the current control method and the sine-wave PWM control method. This device has an IP20-rated open enclosure with natural cooling capabilities.

MR-J3-20A is a servo amplifier from the manufacturer known as Mitsubishi Electric. This device belongs to the Melservo J3 product family. The primary application of this unit is to offer speed, torque, and position control commands to its compatible servo motors. It does this while offering smooth operation. It has a rated voltage range of 200-230 Volts AC, 50/ 60 Hz. Additionally, its frequency fluctuation is ±5% maximum. Also, this unit supports Sinusoidal PWM, or Pulse Width Modulation, control. This servo amplifier also supports the current control system. Furthermore, the MR-J3-20A provides excellent vibration suppression to its compatible servo motors. Some of the other features of this unit include real-time autotuning, improved accuracy, and quick positioning. In addition, users can set this device up flexibly thanks to the Plug and Play feature. The MR-J3-20A servo amplifier has an 8-bit encoder with a resolution of 262,144 p/rev. The MR-J3-20A has a natural-cooling enclosure which is that of an open style. This enclosure has an IP00 Ingress Protection Rating. This servo amplifier also has an integrated regenerative resistor. This resistor has a 10-watt regenerative power rating. Furthermore, this device from Mitsubishi Electric has an integrated dynamic brake. The recommended operating temperature range for this servo amplifier is 0 to 55 °C. Additionally, the recommended storage temperature range for the MR-J3-20A is -20 to 65 °C. Furthermore, this product should only be operated in a setting that has a relative humidity rating of 90%. The MR-J3-20A has an approximate weight of 1.8 pounds (0.8 kilograms).