Zancot Electronics

EtherNet/IP Tap, 3-Port 10/100 Mbps Copper full or half duplex, 24V DC Power, enable single port devices to connect to a ring or linear topology

Operator panel OP7/DP LC display, LED backlit 4-tier, 20 characters/line, SIMATIC S7, M7, PROFIBUS DP 1.5 Mbaud with UL/CSA approval

Fully Integrated Sequence and Process Control for the Ideal Control System for Every Application.The accelerating wave of globalization calls for rebuilding systems to cope with changes in demand. And now OMRON has taken its wealth of technical know-how in factory automation and process control technology to create a PLC-based process control system.Windows is a registered trademark of the Microsoft Corporation. DeviceNet, DeviceNet Safety, CompoNet, and EtherNet/IP are registered trademarks of the ODVA.Other company names and product names are the trademarks or registered trademarks of the respective companies.The over-spec nature of a distributed control system (DCS) increased costs. PLCs, however, could not provide the required process control capabilities, and signal conversion with isolators and other devices was required for I/O. It was just not possible to achieve the ideal system for a specific application.PLCs provide the some of the functions and performance of DCS while also providing the advanced features of PLCs: Open specs, easy maintenance, and cost performance. A wide range of Isolated-type Analog Units helps to save space and greatly reduces system costs.The manufacturer must be relied upon for everything from system construction to maintenance. Even simple changes to parameters cannot be performed in-house. And, it's nearly impossible to use general-purpose devices and software (such as HMI devices or Windows-based software) when modifying the system.Paste function blocks in a window just like you were creating a flow sheet, and then connect the blocks with the mouse to graphically program a wide range of process control. And with a PLC, it's easy to incorporate general-purpose HMI devices and software (such as touch panels and SCADA software).If an error occurs in the active CPU Unit, the standby CPU Unit takes over in an instant (using the hot standby method) so that system operation continues essentially unaffected. Other duplex variations are also possible. For example, instead of duplexing the CPU Unit, Power Supply Unit, and Controller Link Unit, a system can be constructed with a Single-CPU Unit and only a duplex Power Supply Unit or only a duplex Controller Link Unit.Replace Units with power supplied or even while the system is running, including CPU Units (Duplex-CPU system), Power Supply Units, Communications Units, Basic I/O Units, and Special I/O Units.Programming is as simple as combining the function blocks required by the application. To increase the number of controlled loops, just add them to the program. HMI windows can also be created easily using a wide range of utility software.

Advanced touchscreen panel 320 x 240 pixels QVGA- 3.5" TFT - 96 MB.This Magelis GTO IP65 touchscreen operator interface (HMI) is supplied with 24V DC, has a 3.5" color TFT LCD display, 320 x 240 pixels (QVGA), 6 function keys and 96MB EPROM. It also has 1 host + 1 mini-B USB ports, 1 RS232C port and 1 Ethernet TCP/IP port. It is ideal for optimized information and communication with automation systems in industry and infrastructure such as compact machines, handling systems, food & beverage machines and pharmaceutical industry. The screen displays text messages, graphic objects and mimic diagrams, control and configuration of data. Its RS485 host port makes it ideal to supervise and control simple systems and machines. It is easily programmable with Vijeo Designer, with almost not coding needed.

5.7 to 12.1 inch sizes are available.A hand-held version of the NS5 is now available to perform operations at the production site. The NS-series PT's have a complete set of functions that can be used at the production site.  The Smart Active Parts(SAP Library) makes it easy to connect to OMRON PLCs and components, OMRON provides a development environment that requires with no programming and no screen designing. When an error occurs in a Unit in the OMRON PLCs, the Troubleshooter SAP Library provides an easy-tounderstand explanation of the cause of the error as well as the countermeasures. Ladder Monitor come as a Standard Feature. The ladder program can be monitored onsite without a laptop! Ladder monitor lets you monitor PLC program status, search for addresses or instructions, monitor multiple I/O points, and much more. Provides the FA integrated tool package "CX-One" for a Screen Design Software Integrated Simulation come as a Standard Feature. The integrated simulation function simulates ladder programs and screen data simultaneously even without the actual hardware.Screens support 42 languages and the Support Software supports eight. System messages can be displayed in eight languages.Single Port Multi Access (SPMA) come as a Standard Feature. The ladder program and screen data can be transferred from a single port!.Connectable PLCs and devices appear one after another

Fully Integrated Sequence and Process Control for the Ideal Control System for Every Application.The accelerating wave of globalization calls for rebuilding systems to cope with changes in demand. And now OMRON has taken its wealth of technical know-how in factory automation and process control technology to create a PLC-based process control system.Windows is a registered trademark of the Microsoft Corporation. DeviceNet, DeviceNet Safety, CompoNet, and EtherNet/IP are registered trademarks of the ODVA.Other company names and product names are the trademarks or registered trademarks of the respective companies.The over-spec nature of a distributed control system (DCS) increased costs. PLCs, however, could not provide the required process control capabilities, and signal conversion with isolators and other devices was required for I/O. It was just not possible to achieve the ideal system for a specific application.PLCs provide the some of the functions and performance of DCS while also providing the advanced features of PLCs: Open specs, easy maintenance, and cost performance. A wide range of Isolated-type Analog Units helps to save space and greatly reduces system costs.The manufacturer must be relied upon for everything from system construction to maintenance. Even simple changes to parameters cannot be performed in-house. And, it's nearly impossible to use general-purpose devices and software (such as HMI devices or Windows-based software) when modifying the system.Paste function blocks in a window just like you were creating a flow sheet, and then connect the blocks with the mouse to graphically program a wide range of process control. And with a PLC, it's easy to incorporate general-purpose HMI devices and software (such as touch panels and SCADA software).If an error occurs in the active CPU Unit, the standby CPU Unit takes over in an instant (using the hot standby method) so that system operation continues essentially unaffected. Other duplex variations are also possible. For example, instead of duplexing the CPU Unit, Power Supply Unit, and Controller Link Unit, a system can be constructed with a Single-CPU Unit and only a duplex Power Supply Unit or only a duplex Controller Link Unit.Replace Units with power supplied or even while the system is running, including CPU Units (Duplex-CPU system), Power Supply Units, Communications Units, Basic I/O Units, and Special I/O Units.Programming is as simple as combining the function blocks required by the application. To increase the number of controlled loops, just add them to the program. HMI windows can also be created easily using a wide range of utility software.

SIMATIC IFP2200 V2. 22í multi-touch display (16:9) with 1920x1080 pixel resolution. built-in unit. for 24 V DC. display port/DVI interface. including DP/USB cable 1.8 m. on the rear USB. neutral design

SIMATIC IFP1900 V2 PRO. 19 multi-touch display (16:9) with 1920x1080 pixel resolution. PRO variant stand. for 24 V DC. DisplayPort. can be placed up to 100 m away HDBaseT. USB on the rear side. standard design

SIMATIC IFP1900 V2 Extended. 19 multi-touch display (16:9) with 1920x1080 pixel resolution. built-in unit. for 24 V DC. DisplayPort. can be placed up to 100 m away HDBaseT. USB on the rear side. standard design

Panel with Bausch + Strobel frame. OEM MP 377 12í Touch for rear section with customer-specific design INSTALLATION CUTOUT as Standard device. CE. UL/CUL

SIMATIC HMI MTP1500. Unified Comfort Panel. touch operation. 15.6í widescreen TFT display. 16 million colors. PROFINET interface. configurable as of WinCC Unified Comfort V16. contains open-source software. which is provided free of charge see enclosed DVD

SIMATIC HMI, KTP1200 BASIC, BASIC PANEL, KEY AND TOUCH OPERATION, 12? TFT DISPLAY, 65536 COLORS, PROFINET INTERFACE, CONFIGURATION FROM WINCC BASIC V13/ STEP7 BASIC V13, CONTAINS OPEN SOURCE SW WHICH IS PROVIDED FREE OF CHARGE FOR DETAILS SEE CD

SIMATIC Mobile Panel 277 with integrated acknowledgment button, stop button, handwheel, D key-operated switch and two illuminated pushbuttons, configurable with WinCC flexible Standard Version 2005 SP1 or higher or TIA Portal V11 to V14

Flange mount adapter VESA 100/75. INOX. IP65 for PRO devices. additional information. amount and content: see technical data

SIMATIC Touch Panel TP 170B mono blue mode STN display MPI/PROFIBUS DP interface Printer/RS232 interface Slot for CF card configurable with ProTool/Lite as of Version V5.2+SP2

SIMATIC HMI MTP700. Unified Comfort Panel. touch operation. 7í widescreen TFT display. 16 million colors. PROFINET interface. configurable as of WinCC Unified Comfort V16. contains open-source software. which is provided free of charge see enclosed DVD

SIMATIC Touch Panel TP070 5.7? STN display Resistive analog touch

SIMATIC MOBILE PANEL 277 W. INTEGRATED ENABLING BUTTON, CONFIGURABLE WITH WINCC FLEXIBLE STANDARD VERSION 2005 SP1 AND HIGHER OR TIA PORTAL V11 AND HIGHER

SIMATIC HMI MTP2200. Unified Comfort Panel. touch operation. 21.5í widescreen TFT display. 16 million colors. PROFINET interface. configurable from WinCC Unified Comfort V16. contains open-source software. which is provided free of charge See enclosed Blu-Ray

SIMATIC MP 277 8í TOUCH MULTI PANEL W. SMALL FRAME 7.5í TFT DISPLAY 6 MB CONFIGURING MEMORY. CONFIGURABLE WITH WINCC FLEXIBLE 2005 STANDARD SP1

SIMATIC HMI CONNECTION BOX COMPACT FOR MOBILE PANELS, CABINET SOLUTION, PROFINET AND PROFISAFE, CONNECTIVITY TO SAFETY RELAIS, CONNECTION POINT RECOGNITION

SIMATIC HMI KTP700 MOBILE. 7.0í TFT DISPLAY. 800 X 480 PIXELS.16M COLOR. KEY AND TOUCH OPERATION. 8 FUNCTION KEYS. 1 X PROFINET/INDUSTRIAL ETHERNET INTERFACE; 1 X MULTIMEDIA CARD. 1 X USB. CONFIGURABLE FROM WINCC COMFORT V13 SP1

SIMATIC IFP2200 pro Flat Panel 22í display (16:9). Multitouch. Full HD resolution. prepared for supporting foot/ expansion elements 1920 x 1080 pixels. for 24 V DC. display port. IP65. Fully enclosed. Ethernet monitor with basic adapter

SIMATIC HMI TP700 Comfort. Comfort Panel. Touch operation. 7í widescreen TFT display. 16 million colors. PROFINET interface. MPI/PROFIBUS DP interface. 12 MB configuration memory. Windows CE 6.0 (Microsoft Support included Security updates discontinued) configurable from WinCC Comfort V11 with Viessmann design

SIMATIC HMI KP400 BASIC COLOR PN, BASIC PANEL, KEY OPERATION, 4? WIDESCREEN-TFT-DISPLAY, 256 COLORS, PROFINET INTERFACE, CONFIGURATION FROM WINCC BASIC V11 SP2/ STEP 7 BASIC V11 SP2, CONTAINS OPEN SOURCE SW WHICH IS PROVIDED FREE OF CHARGE FOR DETAILS SEE CD

SIMATIC FLAT PANEL FP77-12T 12 INCH TOUCH TFT- DISPLAY WITH 800X600 PIXEL RESOLUTION 24V DC AND 110/220V AC VGA. DVI-D INTERFACE INCL. VGA-CABLE 1.8M

SIMATIC MOBILE PANEL 170 WITH INTEGRATED ENABLING BUTTON CONFIGURABLE W. PROTOOL/LITE VERSION V6.0+SP2 AND HIGHER

SIMATIC S7-300 digital input SM 321, Isolated in groups of 16, 64 DI, 24 V DC, 3ms, Sink/source input Terminal blocks 6ES7392-1.N00-0AA0 and cable 6ES7392-4...0-0AA0 required

SIMATIC S7-400, interface module Send IM 460-1 for central coupling with PS transfer, without C bus

SIMATIC S7-300, temperature Control Unit FM 355-2S, 4 channels, Step and pulse, 4 AI+8 DI+8 DO incl. multi-language configuration package, Manual and Getting Started (de, de, fr, en it) on CD-ROM

SIMATIC S7-400, Power supply PS407 4A,120/230 V AC,5 V DC/4 A

SIMATIC S7-300 CPU319F-3 PN/DP, Central processing unit with 2.5 MB work memory, 1st interface MPI/DP 12 Mbit/s, 2nd interface DP master/slave 3rd interface Ethernet PROFINET, Micro Memory Card required

SIMATIC S7-400, CPU 414-3 PN/DP Central processing unit with: Work memory 2.8 MB, (1.4 MB code, 1.4 MB data), interfaces: 1st interface MPI/DP 12 Mbit/s,(X1), 2nd interface Ethernet/PROFINET (X5), 3rd interface IF 964-DP plug-in (IF1)

SIMATIC S7-200, CPU 222 COMPACT UNIT, DC POWER SUPPLY 8 DI DC/6 DO DC 4 KB CODE/2 KB DATA, PROFIBUS DP EXTENDABLE

SIMATIC S7-400, CPU 412-2 Central processing unit with: Work memory 1 MB, (0.5 MB code; 0.5 MB data) 1st interface MPI/DP 12 Mbit/s, 2nd interface PROFIBUS DP,

SIMATIC S7-400, CPU 413-2 DP CENTRAL PROCESSING UNIT WITH: MULTI-POINT MPI INTERFACE INTEGR. PROFIBUS-DP INTERFACE 72 KB WORKING MEMORY

SIMATIC S7-300, DIGITAL OUTPUT SM 322, OPTICALLY ISOLATED, 16 DO, 24V DC, 0.5A, 1 X 20 PIN SUM OF OUTPUT CURRENTS 4A/GROUP (8A/MODULE)

Siemens Sinamics S120 Control Unit Cu310-2-6SL30401LA010AA0

PanelView 600 Color Terminal 6-inch, Keypad, Remote I/O Communication & RS-232 Printer Port, AC Power