Zancot Electronics

This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N and should be read and understood before attempting to install or use the unit. • If in doubt at any stage during the installation of the FX2N always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the FX2N please consult the nearest Mitsubishi Electric distributor. • This manual is subject to change without notice.Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, (trained and qualified to the local and national standards required to fulfill that role). These engineers should be fully aware of all aspects of safety with regards to automated equipment. b) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for the said product. All maintenance should be carried out in accordance with established safety practices. c) All operators of the completed product should be trained to use that product in a safe and co-ordinated manner in compliance to established safety practices. The operators should also be familiar with all documentation which is connected with the actual

This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N and should be read and understood before attempting to install or use the unit. • If in doubt at any stage during the installation of the FX2N always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the FX2N please consult the nearest Mitsubishi Electric distributor. • This manual is subject to change without notice.Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, (trained and qualified to the local and national standards required to fulfill that role). These engineers should be fully aware of all aspects of safety with regards to automated equipment. b) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for the said product. All maintenance should be carried out in accordance with established safety practices. c) All operators of the completed product should be trained to use that product in a safe and co-ordinated manner in compliance to established safety practices. The operators should also be familiar with all documentation which is connected with the actual

Extended Product Type: FX-series Product ID: FX3G-40MT/ESMitsubishi Type Designation: FX-seriesDescription: PLC, FX3G Base Unit AC 100-240 V; 24 inputs DC 24V; 16 transistor outputs.Up to 256 input/output points] The total number of inputs and outputs (128 points maximum) directly connected to the PLC and remote inputs and outputs (128 points maximum) of the CC-Link can be extended to 256 points.The PLC has two built-in variable analog potentiometers available for adjusting the timer set time.For peripheral devices not applicable to FX3G Series, specify FX1N Series for model selection, and you can program the sequence. In this case, use instructions and devices within the ranges common to FX3G Series and the selected model of PLC Use of programming software (GX Works2, GX Developer) enables you to remotely transfer programs and monitor PLC operation through a modem connected to the RS-232C expansion board or RS-232C communication special adapter

This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N and should be read and understood before attempting to install or use the unit. • If in doubt at any stage during the installation of the FX2N always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the FX2N please consult the nearest Mitsubishi Electric distributor. • This manual is subject to change without notice.Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, (trained and qualified to the local and national standards required to fulfill that role). These engineers should be fully aware of all aspects of safety with regards to automated equipment. b) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for the said product. All maintenance should be carried out in accordance with established safety practices. c) All operators of the completed product should be trained to use that product in a safe and co-ordinated manner in compliance to established safety practices. The operators should also be familiar with all documentation which is connected with the actual

This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N and should be read and understood before attempting to install or use the unit. • If in doubt at any stage during the installation of the FX2N always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the FX2N please consult the nearest Mitsubishi Electric distributor. • This manual is subject to change without notice.Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, (trained and qualified to the local and national standards required to fulfill that role). These engineers should be fully aware of all aspects of safety with regards to automated equipment. b) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for the said product. All maintenance should be carried out in accordance with established safety practices. c) All operators of the completed product should be trained to use that product in a safe and co-ordinated manner in compliance to established safety practices. The operators should also be familiar with all documentation which is connected with the actual